all messages for Guix-related lists mirrored at yhetil.org
 help / color / mirror / code / Atom feed
From: "pelzflorian (Florian Pelz)" <pelzflorian@pelzflorian.de>
To: "Ludovic Courtès" <ludo@gnu.org>
Cc: Mathieu Othacehe <othacehe@gnu.org>, 59784@debbugs.gnu.org
Subject: bug#59784: [version 1.4.0rc1] Retrying a failed install fails
Date: Wed, 14 Dec 2022 14:36:16 +0100	[thread overview]
Message-ID: <878rja150v.fsf@pelzflorian.de> (raw)
In-Reply-To: <87h6xyvqr6.fsf@gnu.org> ("Ludovic Courtès"'s message of "Wed, 14 Dec 2022 00:16:29 +0100")

Eventual success, partially.

First of all:

Ludovic Courtès <ludo@gnu.org> writes:
> "pelzflorian (Florian Pelz)" <pelzflorian@pelzflorian.de> skribis:
>> Additionally, I had to do “GUIX_ALLOW_ME_TO_USE_PRIVATE_COMMIT=y
>> make update-guix-package”.  Or else the installer was using a Guix that
>> did not have the lines swapped.
> Hmm this is surprising because we’re already using (current-guix) in
> (gnu installer).

Apparently no.  If I commit only those two diffs from your mail, with
`./pre-inst-env guix system image -t iso9660 --label=Guix
gnu/system/install.scm`, then

guix gc --references /gnu/store/*-installer-real

prints a Guix package that does not contain any of the changes to
gnu/installer/final.scm.

Nonetheless I used it and ran the installer with surprising failures
that make me doubt either the health of my USB drive: `guix system
init --fallback` did not download substitutes but said ACL seems to be
uninitialized and fell back to downloading/building the tar.xz
sources.  I pulled the Ethernet plug, resumed the installer to run
`guix system init` again, but this now complains that nss-certs is an
unknown package.  Sending a dump crashed the installer.  On TTY3, `ls
/tmp` tells me '-bash: ls: command not found'.

Another USB drive, another try, the installer again says there's no
ACL and downloads tar.xz, but otherwise behaves as rc2 and sometimes
bugs out when pulling Ethernet; final.scm does not contain the patch.

Is that second diff of yours perhaps really about ACLs?

I do the authorization dance, commit the diff about 'stop-service' and
the update-guix-package, then pull --branch=version-1.4.0.  I can now
resume happily, when pulling the Ethernet and even when pressing
Ctrl-C just for fun.

Except it is necessary to resume twice.  The first resume always fails
and the second resume resumes.  Does it confuse the two databases?

Except after a large number of resumes, not even the second resume
resumes anymore.  I sent a installer-dump-c82c7abf.

I shall try with fsync now.

Regards,
Florian




  reply	other threads:[~2022-12-14 13:38 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-12-02 17:52 bug#59784: [version 1.4.0rc1] Retrying a failed install fails pelzflorian (Florian Pelz)
2022-12-09  9:42 ` Ludovic Courtès
2022-12-09 11:11   ` Ludovic Courtès
2022-12-10  8:39   ` pelzflorian (Florian Pelz)
2022-12-13  9:40     ` Ludovic Courtès
2022-12-13  9:48       ` Ludovic Courtès
2022-12-13 22:22         ` pelzflorian (Florian Pelz)
2022-12-13 23:16           ` Ludovic Courtès
2022-12-14 13:36             ` pelzflorian (Florian Pelz) [this message]
2022-12-14 21:47               ` pelzflorian (Florian Pelz)
2022-12-14 23:50                 ` Ludovic Courtès
2022-12-15 17:46                   ` pelzflorian (Florian Pelz)
2022-12-15 20:44                     ` pelzflorian (Florian Pelz)
2022-12-16 16:57                       ` Ludovic Courtès
2022-12-16 20:28                         ` pelzflorian (Florian Pelz)
2022-12-17 11:01                           ` Ludovic Courtès
2022-12-17 19:36                             ` pelzflorian (Florian Pelz)
2022-12-17 16:15                         ` Ludovic Courtès
2022-12-17 19:27                           ` pelzflorian (Florian Pelz)
2022-12-17 21:30                             ` Ludovic Courtès
2022-12-18  0:23                               ` Ludovic Courtès
2022-12-16 13:55                 ` Maxime Devos
2022-12-16 20:17                   ` pelzflorian (Florian Pelz)
2022-12-18 16:41                 ` pelzflorian (Florian Pelz)
2022-12-12 12:07 ` pelzflorian (Florian Pelz)

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=878rja150v.fsf@pelzflorian.de \
    --to=pelzflorian@pelzflorian.de \
    --cc=59784@debbugs.gnu.org \
    --cc=ludo@gnu.org \
    --cc=othacehe@gnu.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
Code repositories for project(s) associated with this external index

	https://git.savannah.gnu.org/cgit/guix.git

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.