From: ng0 <ng0@pragmatique.xyz>
To: nee <nee@cock.li>
Cc: help-guix@gnu.org
Subject: Re: I installed GuixSD on my laptop
Date: Sat, 3 Jun 2017 22:57:38 +0000 [thread overview]
Message-ID: <20170603225738.gxbczfj4aat3pky3@abyayala> (raw)
In-Reply-To: <86942c60-38fb-7cd4-7162-72705c50c15a@cock.li>
[-- Attachment #1: Type: text/plain, Size: 3921 bytes --]
Hi nee, I just have a quick reply to some of the points below.
Good night!
nee transcribed 2.9K bytes:
> Hello everyone, a few months ago I installed GuixSD 0.12 in a luks
> encrypted partition on my laptop. Here are some problems I have with it
> so far.
>
> 1. How do I set the locale in the login manager and Grub.
> I have a German keyboard, but the system boots with an english
> key-setting and only changes when I enter gnome or xfce (I had to set
> them up via their guis). Is there any GuixSD-level setting for this? The
> install manual didn't mention it.
> It's a real pain to enter my password like this.
This is a feature-bug in SLiM and whatever this other login manager is called.
I reported a bug on this, and a partial workaround exists. I hope that
lightdm can deal with this better. More on the solution either tomorrow or
by someone else in the meantime.
> 2. I have to enter my disk-encryption-password two times on every boot.
> Once before grub and one time when shepard boots up. I have my
> bootloader on a diferent drive, might this be related to the issue?
This also happens when it is just on one drive. I think there exist
cryptsetup solutions with detached heads etc which make this easier
to deal with. I haven't tested it in practice.
> 3. When I enter one wrong password on the first disk-encryption-prompt
> (before grub) I get thrown into a grub console. It should give me a few
> more tries.
>
> 4. ibus is not working in xfce. I copied the paths from the popup of
> ibus-setup into my .bashrc, but even after login out, I couldn't get any
> program to actually use ibus. I also had no success in gnome later. I
> was trying to get Japanease input to work.
Can you report a bug on this or check if there's a bug already reported for it?
I'm also looking to update the whole lot of XFCE, but this might not solve
your problem.
> 5. I've been using thunderbird with Enigmail previously. I think I read
> on irc that icedove would be the way to go, and that it hasn't been
> packaged yet.
> Enigmail is really neat, so I wouldn't want to be without it.
>
> 6. My laptop has an Nvidia and an Intel graphics card, how do I force
> intel to be active?
> The Nouveau drivers can't do any 3d stuff at a bearable framerate,
> probably due to it's dependence on blobs.
> I wonder if Intel would perform better. How would I switch between them
> on GuixSD?
>
> 7. I have this wifi stick:
> https://www.thinkpenguin.com/gnu-linux/penguin-wireless-n-usb-adapter-gnu-linux-tpe-n150usb
> Is the driver already packaged for guixsd?
>
> * An unrelated story:
> I had to install GuixSD twice, because I forgot to punch "(dependencies
> mapped-devices)" into my file-system configuration.
> So shepard would not boot up properly and after some time I got a guile
> debug repl.
> I see that this is my own fault, for not reading the docs properly.
> I hope the new ncurses installer will help to prevent such mistakes.
>
> * Not a problem: Touchpad works different
> My first observation was that the touchpad was not working correctly.
> The touchpad only works for mouse movement.
> Clicking by tapping any point on the pad does not work.
> Scrolling by moving down/up the right edge does not work.
>
> I use the hardware buttons below it for clicking, but I wonder, aren't
> there some laptops without those?
> Later I found out that scrolling works with two fingers and this whole
> setup is actually much better, since I do way less misclicks that way!
>
> * xf86-input-synaptics?
> Because I previously tried nixos I directly installed
> xf86-input-synaptics with my installation. I never tried to use my
> system without it. If it is required it should be mentioned in the docs.
>
> Have a nice day, and happy hacking on GuixSD!
>
>
--
ng0
OpenPG: A88C8ADD129828D7EAC02E52E22F9BBFEE348588
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
next prev parent reply other threads:[~2017-06-03 22:57 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-03 20:53 I installed GuixSD on my laptop nee
2017-06-03 22:57 ` ng0 [this message]
2017-06-04 0:32 ` someone
2017-06-05 19:48 ` Ludovic Courtès
2017-06-04 11:15 ` pelzflorian (Florian Pelz)
2017-06-04 19:35 ` Arun Isaac
2017-06-05 19:53 ` Ludovic Courtès
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170603225738.gxbczfj4aat3pky3@abyayala \
--to=ng0@pragmatique.xyz \
--cc=help-guix@gnu.org \
--cc=nee@cock.li \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
Code repositories for project(s) associated with this external index
https://git.savannah.gnu.org/cgit/guix.git
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.