fonts for Chinese charset

fonts for Chinese charset

[Eric Abrahamsen]

So rather than attempting to hijack the other utf char display thread,  
I'll ask my question in a new one...

My issue, it turns out, is that without defining any font stuff  
whatsoever, emacs interprets most of my Chinese characters as Japanese  
(presumably the Chinese character which exist as kanji in Japanese).  
My language environment and preferred coding system is utf-8, but  
running C-u C-x = on a Chinese character shows it as charset japanese- 
jisx0208, encoded by mule-utf-8. I recently set the default font to  
Inconsolata, which resulted in more (about half) of the characters  
being interpreted as a Chinese charset (chinese-gb2312), and also a  
very different font being used for the "Japanese" and "Chinese"  
characters. I thought this was where my problems started, in fact they  
were existing problems highlighted by the use of obviously different  
fonts.

Running C-h C RET and looking at the coding system priority list, it  
starts off with mule-utf-8, and then there are a few japanese coding  
systems further down (but no chinese). I thought if I used prefer- 
coding-system to set the first priority to mule-utf-8 and the second  
to gb2312 that might help, but it seems to have made no difference.  
Presumably this is because charsets and coding systems are not the  
same thing.

Is there anything I can do to help emacs recognize all Chinese  
characters as Chinese? My end goal is just to get emacs to use the  
same (Chinese) font for all Chinese characters. I'm using Carbon emacs  
(based on 22.3.1) on a Mac...

Thanks!
Eric

Re: fonts for Chinese charset

[Eric]

Nevermind! I compiled emacs 23 and all works well. All characters
report their character set as unicode (or unicode bmp for Chinese
chars) and while it's using a hideous Chinese font I'll bet I can
figure that one out on my own.

E


On Jun 14, 12:10 pm, Eric Abrahamsen <gir...@gmail.com> wrote:
> So rather than attempting to hijack the other utf char display thread,  
> I'll ask my question in a new one...
>
> My issue, it turns out, is that without defining any font stuff  
> whatsoever, emacs interprets most of my Chinese characters as Japanese  
> (presumably the Chinese character which exist as kanji in Japanese).  
> My language environment and preferred coding system is utf-8, but  
> running C-u C-x = on a Chinese character shows it as charset japanese-
> jisx0208, encoded by mule-utf-8. I recently set the default font to  
> Inconsolata, which resulted in more (about half) of the characters  
> being interpreted as a Chinese charset (chinese-gb2312), and also a  
> very different font being used for the "Japanese" and "Chinese"  
> characters. I thought this was where my problems started, in fact they  
> were existing problems highlighted by the use of obviously different  
> fonts.
>
> Running C-h C RET and looking at the coding system priority list, it  
> starts off with mule-utf-8, and then there are a few japanese coding  
> systems further down (but no chinese). I thought if I used prefer-
> coding-system to set the first priority to mule-utf-8 and the second  
> to gb2312 that might help, but it seems to have made no difference.  
> Presumably this is because charsets and coding systems are not the  
> same thing.
>
> Is there anything I can do to help emacs recognize all Chinese  
> characters as Chinese? My end goal is just to get emacs to use the  
> same (Chinese) font for all Chinese characters. I'm using Carbon emacs  
> (based on 22.3.1) on a Mac...
>
> Thanks!
> Eric

Re: fonts for Chinese charset

[Eric]

On Jun 14, 3:08 pm, Eric <gir...@gmail.com> wrote:
> Nevermind! I compiled emacs 23 and all works well. All characters
> report their character set as unicode (or unicode bmp for Chinese
> chars) and while it's using a hideous Chinese font I'll bet I can
> figure that one out on my own.

And I did, eventually:

(set-fontset-font
 (frame-parameter nil 'font) 'chinese-gb2312 '("STKaiti" . "unicode-
bmp"))


>
> E
>
> On Jun 14, 12:10 pm, Eric Abrahamsen <gir...@gmail.com> wrote:
>
>
>
> > So rather than attempting to hijack the other utf char display thread,  
> > I'll ask my question in a new one...
>
> > My issue, it turns out, is that without defining any font stuff  
> > whatsoever, emacs interprets most of my Chinese characters as Japanese  
> > (presumably the Chinese character which exist as kanji in Japanese).  
> > My language environment and preferred coding system is utf-8, but  
> > running C-u C-x = on a Chinese character shows it as charset japanese-
> > jisx0208, encoded by mule-utf-8. I recently set the default font to  
> > Inconsolata, which resulted in more (about half) of the characters  
> > being interpreted as a Chinese charset (chinese-gb2312), and also a  
> > very different font being used for the "Japanese" and "Chinese"  
> > characters. I thought this was where my problems started, in fact they  
> > were existing problems highlighted by the use of obviously different  
> > fonts.
>
> > Running C-h C RET and looking at the coding system priority list, it  
> > starts off with mule-utf-8, and then there are a few japanese coding  
> > systems further down (but no chinese). I thought if I used prefer-
> > coding-system to set the first priority to mule-utf-8 and the second  
> > to gb2312 that might help, but it seems to have made no difference.  
> > Presumably this is because charsets and coding systems are not the  
> > same thing.
>
> > Is there anything I can do to help emacs recognize all Chinese  
> > characters as Chinese? My end goal is just to get emacs to use the  
> > same (Chinese) font for all Chinese characters. I'm using Carbon emacs  
> > (based on 22.3.1) on a Mac...
>
> > Thanks!
> > Eric